Reply
Aug 14 2009
By: Dejuanxg Wastelander 747 posts
Offline

Complete List Of Psp Error Codes & What They Mean!

8 replies 14110 views Edited Aug 14, 2009

I stumbled upon this and had to share because I always found those errors annoying because I never knew what they meant. Btw all comments are welcome!

 

 

Normal errors 
The first 4 numbers gives information about the place of the error: 8002XXXX = Kernel 8001XXXX = The standard libc 


00000001 Internal Error 1. Reset your settings to default 2. Theres no WiFi point found 

80020148 The game could not be started If you're under an Official Firmware you can't run homebrew, downgrade/upgrade to an Custom Firmware. 

8002013C Error in the flash memory of the PSP. Try to restore your flash0-backup or re-install the Custom Firmware. 

80020321 The game could not be started Check if you configured kernel or UMD/ISO mode right. 

8008273A Internal Error Reset your settings to default 

80108D50 PSP Camera not connected 

80410A0B Hardware Error WiFi is damaged. 

IDstorage errors 
DRNFFFFFFD8 = key 0x4 missing DRNFFFFFFD7 = key 0x4 header is not "n y r B" (in hex: 6E 79 72 42) 

DRNFFFFFFCE = key 0x5 missing DRNFFFFFFCD = key 0x5 header is not "g k l C" (in hex: 67 6B 6C 43) 

DRNFFFFFFC4 = key 0x6 missing DRNFFFFFFC3 = key 0x6 header is not "r d D M" (in hex: 72 64 44 4D) 

Errors with TA-086 PSP motherboards: 

DRNFFFFFFB9 = key 0x7 header is not "D a P A" (in hex: 44 61 50 41) 

DRNFFFFFFB0 = key 0x8 missing DRNFFFFFFAF = key 0x8 header is not "p D C L" (in hex: 70 44 43 4C) 

You can repair this with IdStorage Manager. 

For key 08 errors make a new key 08 by adding this line: "70 44 43 4C 01 00 00 00 0C 00 00 00 76 FC 19 C8 0A 00 19 00 10 00 0D 00 07 00 02" and than 00 untill the end. 

CTA80000025 = region key (0x0100) is damaged or missing (You only can repair this with your OWN backup). 




Errorlist: 
UKN9000001 = The update cannot be started. The data is corrupted. 
80110305 = Load failed.The Memory Stick™ could not be acessed. 
80010013 = device / media not found 
8001B002 = unknown 
80020001 or 800244C = kernel errors 
80020001 = generic kernel error (default) 
800200D9 = failed to allocate the memory block 
80020130 = file read error 
80020148 = PRX type unsupported 
80110482 = occurs when test of WLAN infrastructure connection fails 
FFFFFED3 = unknown (might be decryption error) 
80410001 or 80410D16 = network errors 
80410D07 = unknown (possibly WLAN) 
ffffffff = PSP update failed 
80410A0B = Internal Error 
8041040F = DNS Error, unable to connect to server 
80410410 = Cannot connect to the given acess point 
80010087 = The game could not be started 
0x0 = no error 
0x80020001 = error 
0x80020002 = not implemented 
0x80020032 = illegal exception code 
0x80020033 = exception handler not use 
0x80020034 = exception handler already used 
0x80020035 = system call table notuse 
0x80020036 = system call table alraady used 
0x80020037 = illegal system call table 
0x80020038 = illegal Primary Syscall number 
0x80020039 = Primary Syscall number already use 
0x80020064 = call from interrupt handler/thread 
0x80020065 = illegal INTRCODE 
0x80020066 = CPU already interrupt disable 
0x80020067 = Handler already exist 
0x80020068 = Handler not found 
0x80020069 = illegal interrupt level 
0x8002006a = illegal address 
0x8002006b = illegal IntrHandler Option Paramsize 
0x8002006c = illegal stackad dress 
0x8002006d = alreadystackad dressset 
0x80020096 = not found free Hard Timer 
0x80020097 = illegal timer ID 
0x80020098 = illegal source 
0x80020099 = illegal prescale 
0x8002009a = Hard Timer in use 
0x8002009b = Hard Timer not setup 
0x8002009c = Hard Timer not in use 
0x800200a0 = unit number already used 
0x800200a1 = unit number notused 
0x800200a2 = rom directory notfound 
0x800200c8 = id type already exist 
0x800200c9 = id type not exist 
0x800200ca = {not available} 
0x800200cb = unknown UID 
0x800200cc = unmatch UID type 
0x800200cd = id not exist 
0x800200ce = not found UID function 
0x800200cf = UID already holder 
x800200d0 = UID not holer 
0x800200d1 = illegal permission 
0x800200d2 = illegal argument 
0x800200d3 = illegal adress 
0x800200d4 = the memory area is out ofrange 
0x800200d5 = the memory areais over lap 
0x800200d6 = illegal partitionid 
0x800200d7 = partition in use 
0x800200d8 = illegal memory block allocation type 
0x800200d9 = failed toal loca the memory block 
0x800200da = inhibitedtores izethismemoryblock 
0x800200db = failedtoresize thismemoryblock 
0x800200dc = failedtoalloca teheapblock 
0x800200dd = failedtoalloca teheap 
0x800200de = illegalchunkid 
0x800200df = cannotfindchun kname 
0x800200e0 = thereisnofreec hunk 
0x8002012c = modulelinkerro r 
0x8002012d = illegalobjectf ormat(notPRX/PFX) 
0x8002012e = notfoundModule 
0x8002012f = notfoundModule file 
0x80020130 = Modulefileread error 
0x80020131 = memoryinuse 
0x80020132 = partitionmisma tch 
0x80020133 = modulealreadys tarted 
0x80020134 = modulenotstart edyet 
0x80020135 = modulealreadys topped 
0x80020136 = modulecannotst op 
0x80020137 = modulenotstopp edyet 
0x80020138 = modulecannotre move 
0x80020139 = exclusiveload 
0x8002013a = Libraryisnotli nkedyet 
0x8002013b = Libraryalready exists 
0x8002013c = Librarynotfoun d 
0x8002013d = illegalLibrary header 
0x8002013e = Libraryisusedn ow 
0x8002013f = modulealreadys topping 
0x80020140 = illegaloffsetv alue 
0x80020141 = illegalpositio ncode 
0x80020142 = illegalaccessc ode 
0x80020143 = modulemanagerb usy 
0x80020144 = illegalflag 
0x80020145 = cannotgetmodul elist 
0x80020146 = prohibitLoadMo duledevice 
0x80020147 = prohibitLoadEx ecdevice 
0x80020148 = unsupportedPRX type 
0x80020149 = illegalpermiss ioncall 
0x8002014a = cannotgetmodul einformation 
0x8002014b = illegalLoadExe cbuffer 
0x8002014c = illegalLoadExe cfilename 
0x8002014d = Thereisnoexitc allback 
0x80020190 = nomemory 
0x80020191 = illegalattrpar ameter 
0x80020192 = illegalthreade ntryaddress 
0x80020193 = illegalpriorit yvalue 
0x80020194 = illegalstacksi ze 
0x80020195 = illegalmode 
0x80020196 = illegalmask 
0x80020197 = illegalthreadI D 
0x80020198 = notfoundthread 
0x80020199 = notfoundsemaph ore 
0x8002019a = notfoundeventf lag 
0x8002019b = notfoundmessag ebox 
0x8002019c = notfoundVpool 
0x8002019d = notfoundFpool 
0x8002019e = notfoundmessag epipe 
0x8002019f = notfoundalarm 
0x800201a0 = notfoundthread eventhandler 
0x800201a1 = notfoundcallba ck 
0x800201a2 = threadalreadyD ORMANT 
0x800201a3 = threadalreadyS USPEND 
0x800201a4 = threadisnotDOR MANT 
0x800201a5 = threadisnotSUS PEND 
0x800201a6 = threadisnotWAI T 
0x800201a7 = nowdispatchdis abled 
0x800201a8 = WAITtimeout 
0x800201a9 = WAITcanceled 
0x800201aa = WAITstatusrele ased 
N0x800201ab = WAITstatusrel easedwithcallback 
0x800201ac = threadistermin ated 
0x800201ad = semaphorecount erzero 
0x800201ae = semaphorecount eroverflow 
0x800201af = eventflagcondi tionnotoccur 
0x800201b0 = thiseventflagc annotacceptwaitswithmulti plethreads 
0x800201b1 = illegaleventfl agwaitpattern 
0x800201b2 = messageboxhave nomessage 
0x800201b3 = messagepipeisf ull 
0x800201b4 = messagepipeise mpty 
0x800201b5 = waitobjectdele ted 
0x800201b6 = illegalmemoryb lock 
0x800201b7 = illegalmemorys ize 
0x800201b8 = illegalscratch padaddress 
0x800201b9 = scratchpadinus e 
0x800201ba = scratchpadnoti nuse 
0x800201bb = illegaltype 
0x800201bc = illegalsize 
0x800201bd = illegalcount 
0x800201be = notfoundvtimer 
0x800201bf = illegalvtimerI D 
0x800201c0 = illegalKTLSID 
0x800201c1 = KTLSisfull 
0x800201c2 = KTLSisbusy 
0x80020258 = invalidsuchpri ority 
0x80020259 = devicenameisin valid 
0x8002025a = devicenameisun known 
0x8002025b = pminformationi sregisteredalready 
0x8002025c = pminformationi snotregistered 
0x8002025d = majorstateisin validvalue 
0x8002025e = requestisinval id 
0x8002025f = requestisunkno wn 
0x80020260 = unitnumberisin valid 
0x80020261 = cannotcancelre quest 
0x80020262 = pminformationi sinvalid 
0x80020263 = argumentisinva lid 
0x80020264 = alreadytargete powerstate 
0x80020265 = failedtochange systempowerstate 
0x80020266 = cannotchangede vicepowerstate 
0x80020267 = devicedoesnots upportsuchpowerstate 
0x800202bc = requesttotheDM ACfailed 
0x800202bd = DMAoperationis lessorequalone 
0x800202be = theoperationis alreadyqueued 
0x800202bf = theoperationis alreadyfinishedornotqueue ud 
0x800202c0 = theoperationis alreadyintransferprogress 
0x800202c1 = theoperationis notassignedyet 
0x800202c2 = thesyncoperati ontimedout 
0x800202c3 = dmaoperationst ructisalreadyfreed 
0x800202c4 = dmaoperationis used 
0x800202c5 = dmaoperationis empty 
0x800202c6 = DMAoperationis aborted 
0x800202c7 = DMAoperationis error 
0x800202c8 = physicalDMAcha nnelisalreadyreserved 
0x800202c9 = physicalDMAcha nnelisnotmanagedbydmacman ager 
0x800202ca = thereisaprivil egeaddressinlinklist 
0x800202cb = linklistbuffer isnotenough 
0x800202cc = theoperationis notassignedtophysicalDMAc hannel 
0x800202cd = theoperationis childoperation 
0x800202ce = itistoomuchtha ntransferabledatasize 
0x800202cf = argumentisinva lid 
0x80020320 = Toomanyopenfil es 
0x80020321 = Nosuchdevice 
0x80020322 = Cross-devicelink 
0x80020323 = Badfiledescrip tor 
0x80020324 = Invalidargumen t 
0x80020325 = Unsupportedope ration 
0x80020326 = Aliasisalready used 
0x80020327 = Cannotmount 
0x80020328 = Driverdeleted 
0x80020329 = Asyncoperation isbusy 
0x8002032a = Noasyncoperati on 
0x8002032b = Deviceisalread yregistered 
0x8002032c = Nocurrentworki ngdirectory 
0x8002032d = Filenametoolon g 
0x800203e8 = DECI3Nosuchdev iceoraddress 
0x800203e9 = DECI3I/Oerror 
0x800203ea = DECI3Notenough core 
0x800203eb = STDIOnotopened 
0x8002044c = Parameterisnot cachealigned 
0x8002044d = Endofkernelerrorcode.Neverusethisname 
CA000005 - keys.bin not found when trying to run a PS1 game. 
DADADADA - Running a FW Update in DAX custom FW 
FFFFFFFF - PSP update failed 
UKN9000001 - update cant start, data corrupt 
00000001 - WiFi error. Occurs when no access points are detected in official 3.7X and custom 3.7X firmware. 
80010087 - Error reading UMD or UMD not present 
80110305 - Load failed.The Memory Stick could not be acessed 
80020148 - Unsupported PRX type | This error also seems to appear when you are running an iso with a fake mem. stick 
8001006F - Remote Play connection error. Most likely when no PS3 is sending a signal over your network. 
800200D1 - Ran homebrew without Homebrew enabled firmware. 
8002014C - Ran kxploited homebrew without Homebrew enabled firmware. 
80020321 - Ran a game that doesn't support NO-UMD* (DAX FW ONLY!) 
80110404 - Network error, try restore default settings to fix 
80000004 - its just a general error code that the PSP spits out when it doesnt understand something could mean anything 
80110307 - Load Failed There is no Data available 
80010002 - Putting the POPS EBOOT in the wrong folder 
80000001 - Got it when trying to run PSP filer version 3.6 on 3.40* firmware 
80410A0B - Loose WiFi card 
80020321 - No umd in drive when no umd is disabled 
80110305 = Load failed.The Memory Stick could not be acessed 
8001006F - Remote Play connection error. Most likely when no PS3 is sending a signal over your network 
80020148 - Unsupported PRX type 
800200D1 - Ran homebrew without Homebrew enabled firmware 
8002014C - Ran kxploited homebrew without Homebrew enabled firmware 
80020321 - No umd in drive when no umd is disabled / Ran a game that doesn't support NO-UMD / "No-UMD Mode" 
98765432 - Selected a language who's font has been removed. DAX FW ONLY ERROR! 
80020148 - (unsupported PRX type)? 
800201A8 - (WAIT timeout)? 
80020130 - File Read Error (ex. length is 0) 
80020001 - Generic Kernel Error - default (ex. executable is invalid) 
800200D9 - Failure to allocate memory block (ex. missing PSP) 
80410D07 - Connection error has occurred. (Ie cant find access pt) 
80020001 - error 
80020002 - not implemented 
80020032 - illegal exception code 
80020033 - exception handler not use 
80020034 - exception handler already used 
80020035 - system call table not use 
80020036 - system call table already used 
80020037 - illegal system call table 
80020038 - illegal Primary Syscall number 
80020039 - Primary Syscall number already use 
80020064 - call from interrupt handler/thread 
80020065 - illegal INTRCODE 
80020066 - CPU already interrupt disable 
80020067 - Handler already exist 
80020068 - Handler not found 
80020069 - illegal interrupt level 
8002006a - illegal address 
8002006b - illegal Intr Handler Option Param size 
8002006c - illegal stack address 
8002006d - already stack address set 
80020096 - not found free Hard Timer 
80020097 - illegal timer ID 
80020098 - illegal source 
80020099 - illegal prescale 
8002009a - Hard Timer in use 
8002009b - Hard Timer not setup 
8002009c - Hard Timer not in use 
800200a0 - unit number already used 
800200a1 - unit number not used 
800200a2 - rom directory not found 
800200c8 - id type already exist 
800200c9 - id type not exist 
800200ca - {not available} 
800200cb - unknown UID 
800200cc - unmatch UID type 
800200cd - id not exist 
800200ce - not found UID function 
800200cf - UID already holder 
x800200d0 - UID not holder 
800200d1 - illegal permission 
800200d2 - illegal argument 
800200d3 - illegal address 
800200d4 - the memory area is out of range 
800200d5 - the memory area is overlap 
800200d6 - illegal partition id 
800200d7 - partition in use 
800200d8 - illegal memory block allocation type 
800200d9 - failed to allocate memory block 
800200da - inhibited to resize this memory block 
800200db - failed to resize this memory block 
800200dc - failed to allocate heap block 
800200dd - failed to allocate heap 
800200de - illegal chunk id 
800200df - cannot find chunk name 
800200e0 - there is no free chunk 
8002012c - module link error 
8002012d - illegal object format (not PRX/PFX) 
8002012e - not found Module 
8002012f - not found Module file 
80020130 - Module file read error 
80020131 - memory in use 
80020132 - partition mismatch 
80020133 - module already started 
80020134 - module not started yet 
80020135 - module already stopped 
80020136 - module cannot stop 
80020137 - module not stopped yet 
80020138 - module cannot remove 
80020139 - exclusive load 
8002013a - Library is not linked yet 
8002013b - Library already exists 
8002013c - Library not found 
8002013d - illegal Library header 
8002013e - Library isused now 
8002013f - module already stopping 
80020140 - illegal off set value 
80020141 - illegal position code 
80020142 - illegal access code 
80020143 - module manager busy 
80020144 - illegal flag 
80020145 - cannot get module list 
80020146 - prohibit Load Module device 
80020147 - prohibit Load Exec device 
80020148 - unsupported PRX type 
80020149 - illegal permission call 
8002014a - cannot get module information 
8002014b - illegal Load Exec buffer 
8002014c - illegal Load Exec file name 
8002014d - There is no exit callback 
80020190 - no memory 
80020191 - illegal attr parameter 
80020192 - illegal thread entry address 
80020193 - illegal priority value 
80020194 - illegal stack size 
80020195 - illegal mode 
80020196 - illegal mask 
80020197 - illegal thread ID 
80020198 - not found thread 
80020199 - not found semaphore 
8002019a - not found event flag 
8002019b - not found message box 
8002019c - not found Vpool 
8002019d - not found Fpool 
8002019e - not found message pipe 
8002019f - not found alarm 
800201a0 - not found thread event handler 
800201a1 - not found callback 
800201a2 - thread already DORMANT 
800201a3 - thread already SUSPEND 
800201a4 - thread is not DORMANT 
800201a5 - thread is not SUSPEND 
800201a6 - thread is not WAIT 
800201a7 - now dispatch disabled 
800201a8 - WAIT timeout 
800201a9 - WAIT canceled 
800201aa - WAIT status released 
N800201ab - WAIT status released with callback 
800201ac - thread is terminated 
800201ad - semaphore counter zero 
800201ae - semaphore counter overflow 
800201af - event flag condition not occur 
800201b0 - this event flag cannot accept waits with multiple threads 
800201b1 - illegal event flag wait pattern 
800201b2 - message box have no message 
800201b3 - message pipe is full 
800201b4 - message pipe is empty 
800201b5 - wait object deleted 
800201b6 - illegal memory block 
800201b7 - illegal memory size 
800201b8 - illegal scratchpad address 
800201b9 - scratch pad in use 
800201ba - scratchpad not in use 
800201bb - illegal type 
800201bc - illegal size 
800201bd - illegal count 
800201be - not found vtimer 
800201bf - illegal vtimer ID 
800201c0 - illegal KTLS ID 
800201c1 - KTLS is full 
800201c2 - KTLS is busy 
80020258 - invalid such priority 
80020259 - device name is invalid 
8002025a - device name is unknown 
8002025b - pm information is registered already 
8002025c - pm information is not registered 
8002025d - major state is invalid value 
8002025e - request is invalid 
8002025f - request is unknown 
80020260 - unit number is invalid 
80020261 - cannot cancel request 
80020262 - pm information is invalid 
80020263 - argument is invalid 
80020264 - already target epower state 
80020265 - failed to change system power state 
80020266 - cannot change device power state 
80020267 - device does not support such power state 
800202bc - request to the DMAC failed 
800202bd - DMA operation is less or equal one 
800202be - the operation is already queued 
800202bf - the operation is already finished or not queueud 
800202c0 - the operation is already in transfer progress 
800202c1 - the operation is not assigned yet 
800202c2 - the sync operation timed out 
800202c3 - dma operation struct is already freed 
800202c4 - dma operation is used 
800202c5 - dma operation is empty 
800202c6 - DMA operation is aborted 
800202c7 - DMA operation is error 
800202c8 - physical DMA channel is already reserved 
800202c9 - physical DMA channel is not managed by dmac manager 
800202ca - there is a privilege address in link list 
800202cb - link list buffer is not enough 
800202cc - the operation is not assigned to physical DMA channel 
800202cd - the operation is child operation 
800202ce - it is too much than transferable datasize 
800202cf - argument is invalid 
80020320 - Too many open files 
80020321 - No such device 
80020322 - Cross-device link 
80020323 - Bad file descriptor 
80020324 - Invalid argument 
80020325 - Unsupported operation 
80020326 - Alias is already used 
80020327 - Cannot mount 
80020328 - Driver deleted 
80020329 - Async operation is busy 
8002032a - No async operation 
8002032b - Device is already registered 
8002032c - No current working directory 
8002032d - Filename too long 
800203e8 - DECI3 No such device or address 
800203e9 - DECI3 I/O error 
800203ea - DECI3 Not enough core 
800203eb - STDIO not opened 
8002044c - Parameter is not cache aligned 

8002044d - End of kernel error code Never use this name 

Message 1 of 9 (14,110 Views)
Uncharted Territory
Registered: 08/28/2008
Offline
1569 posts
 

Re: Complete List Of Psp Error Codes & What They Mean!

Aug 14, 2009
wow thanks dude! definitely saving this to a document. kudos to you for sharing this where ever you got it from

Message 2 of 9 (14,110 Views)
Reply
0 Likes
Hekseville Citizen
Registered: 06/15/2009
Offline
300 posts
 

Re: Complete List Of Psp Error Codes & What They Mean!

Aug 14, 2009

Dejuanxg wrote:


80020148 The game could not be started If you're under an Official Firmware you can't run homebrew, downgrade/upgrade to an Custom Firmware. 

8002013C Error in the flash memory of the PSP. Try to restore your flash0-backup or re-install the Custom Firmware. 


 

This thread is due to be locked shortly.

Message 3 of 9 (14,110 Views)
Reply
0 Likes
Hekseville Citizen
Registered: 07/01/2009
Offline
394 posts
 

Re: Complete List Of Psp Error Codes & What They Mean!

Aug 14, 2009
Wow........... The PSP has got a lot of issues lol
Boom-shacka-lacka \m/

Syphon Filter Series: lofiweapwn
SOCOM FTB2: weapwnoffate
PSN server games: lofiweapwn
Star Wars Elite Squadron: lofirebel
Killzone: Liberation: lofizwner
Message 4 of 9 (14,110 Views)
Reply
0 Likes
Wastelander
Registered: 07/09/2009
Offline
809 posts
 

Re: Complete List Of Psp Error Codes & What They Mean!

Aug 14, 2009
Long Eefing list this thread is going to be locked.-I assume.
DO YOU LIKE BACON?......Well I Do......
Message 5 of 9 (14,110 Views)
Reply
0 Likes
Wastelander
Registered: 03/29/2007
Offline
747 posts
 

Re: Complete List Of Psp Error Codes & What They Mean!

Aug 15, 2009
To Everying Posting here saying that this will be locked soon shut up just repeating what someone else has already said only makes it look like you are post count shopping because it won't get locked any faster.
Message 6 of 9 (14,110 Views)
Reply
0 Likes
Hekseville Citizen
Registered: 04/14/2009
Offline
372 posts
 

Re: Complete List Of Psp Error Codes & What They Mean!

Aug 15, 2009
How did you find all this out? O.O
Message 7 of 9 (14,110 Views)
Reply
0 Likes
First Son
Registered: 04/08/2012
Offline
2 posts
 

Re: Complete List Of Psp Error Codes & What They Mean!

Apr 13, 2012

my psp droped in water and after this accident it show me message that I write below:

The system storage cannot be read.
Go to (Setting) > (System Setting) to
format the  system storage.

and when I go to "system setting" and "Format system storage" show me "Format failed. (802E1010) "

Please lead & help me how can I repair my device?

What is my device problem & What that (my error code) means?

thank u

Message 8 of 9 (14,110 Views)
Reply
0 Likes
First Son
Registered: 07/30/2015
Offline
1 posts
 

Re: Complete List Of Psp Error Codes & What They Mean!

Jul 30, 2015
thank you so much,but how do i fix the internet problem if the internet is working and i keep getting the error on my psp? Please reply back to email. Smiley Very Happy
Message 9 of 9 (5,515 Views)
Reply
0 Likes